Usg Installation Manual

Posted on
  1. 135 x 135 x 28.3 mm (5.32 x 5.32 x 1.11 ') Weight. 366 g (12.9 oz) Networking Interfaces. Serial Console Port (1) RJ45 Serial Port: Data Ports (3) 10/100/1000 Ethernet Ports: Max. Power Consumption. 12VDC, 1A Power Adapter (Included) Supported Voltage Range. System: Status: Serial Console.
  2. 135 x 135 x 28.3 mm (5.32 x 5.32 x 1.11 ') Weight. 366 g (12.9 oz) Networking Interfaces. Serial Console Port (1) RJ45 Serial Port: Data Ports (3) 10/100/1000 Ethernet Ports: Max. Power Consumption. 12VDC, 1A Power Adapter (Included) Supported Voltage Range. System: Status: Serial Console.

Usgs National Field Manual

Power Cord
Cage Nuts (Qty. 4)
  • Phillips screwdriver
  • Standard-sized, 19 wide rack with a minimum of 1U height available
  • For indoor applications, use Category 5 (or above) UTP cabling approved for indoor use.
  • For outdoor applications, shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the power supply.

    We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti. For more details, visit: ui.com/toughcable

How to Install a USG Suspended Ceiling. Ceilings manufactured by the United States Gypsum Company, or USG, serve as one of the most widely used ceiling systems for commercial and residential. You use a qualified person to install USG Boral plasterboard. Illustrations in this guide are only representative of USG Boral plasterboard products and the appearance and effects that may be achieved by their use. To ensure the information you are using is current, USG Boral recommends you review the latest building information available on. Prior to installation. Y memd ebl r i F Durock™ Shower Tray into the mortar. Check underside of tray to ensure full mortar coverage. 4.Remove integrated cutout template—used for drain hole cutout in subfloor— from shower tray disk prior to installation. Install shower tray disk by fully embedding in the thin-set mortar.

Note: Although the cabling can be located outdoors, the UniFi Gateway itself should be housed inside a protective enclosure.

Usg Ceiling Installation Manual

IMPORTANT: We strongly recommend using UPS backup and power regulation to prevent equipment damage due to stability issues with local AC power.

UniFi Controller System Requirements

  • Linux, Mac OS X, or Microsoft Windows 7/8/10
  • Java Runtime Environment 1.6 (or above)
  • Web Browser: Google Chrome (Other browsers may have limited functionality)
  • UniFi Controller software v4.8 or higher (available at: ui.com/download/unifi)

System LED

Click here for detailed descriptions.

Console Port

RJ45 serial console port for Command Line Interface (CLI) management. Use an RJ45-to-DB9 serial console cable, also known as a rollover cable, to connect the Console port to your computer. Then configure the following settings as needed:

  • Baud rate 115200
  • Data bits 8
  • Parity NONE
  • Stop bits 1
  • Flow control NONE

USB Port

Reserved for future use.

LAN / WAN / SFP Speed/Link/Act LED

Off

No Link

Amber

Link Established at 10/100 Mbps

Flashing Indicates Activity

Green

Link Established at 1000 Mbps

Flashing Indicates Activity

LAN (Ports 1 - 2)

RJ45 ports support 10/100/1000 Ethernet connections. By default, the LAN1 port is set to DHCP Server, and its IP address is 192.168.1.1/24.

WAN (Ports 1 - 2)

RJ45 ports support 10/100/1000 Ethernet connections. A WAN port is active only if the corresponding SFP port is empty. By default, the WAN1 port is set to DHCP Client.

SFP (Ports 1 - 2)

SFP ports are hot-swappable and support 10/100/1000 fiber SFP modules. If an SFP module is plugged in, then the SFP port is active, and the corresponding WAN port is deactivated. By default, the SFP1 port is set to DHCP Client.

Reset Button

Resets to factory defaults. The UniFi Gateway should be running after bootup is complete. Press and hold the Reset button for about 10 seconds until the right LED on the WAN2 port starts flashing and then becomes solidly lit. After a few seconds, the LED will turn off, and the UniFi Gateway will automatically reboot.

Manual

    OR

    Note: The corresponding WAN port will be deactivated.

For information about compatible fiber SFP modules, visit: community.ubnt.com/unifi

By default, the WAN1 port is set to DHCP so it can be assigned network settings by the service provider.To change the setting, connect a computer directly (or through a switch) to the LAN1 port of the UniFi Gateway.

  1. From a web browser, go to: https://setup.ui.com
  2. Enter your Username and Password. Click Sign In.
  3. Note: If the UniFi Gateway has not been adopted by a UniFi Controller, the login window will be skipped and the Setup window will appear.

  4. Click Edit Configuration to configure the WAN1 port as DHCP,Static IP, or PPPoE.

For information on using the UniFi Controller software, refer to the User Guide located on our website at: ui.com/download/unifi

Usg

USG-PRO-4

Dimensions

484 x 44 x 164 mm

(19.06 x 1.73 x 6.46')

Weight

2.30 kg

(5.07 lb)

Networking Interfaces

Serial Console Port(1) RJ45 Serial Port
Data Ports(2) 10/100/1000 RJ45 Ports
(2) 10/100/1000 RJ45/SFP Combination Ports

Max. Power Consumption

40W

Power Supply

Internal AC/DC Power Adapter, 60W (24V, 2.5A)

Supported Voltage Range

110 - 240VAC

LEDs

SystemStatus
Data PortsSpeed/Link/Activity

Layer 3 Forwarding Performance

Packet Size: 64 Bytes2,400,000 pps
Packet Size: 512 Bytes or Larger4 Gbps (Line Rate)

Processor

Dual-Core 1 GHz, MIPS64 with Hardware Acceleration for Packet Processing

System Memory

2 GB DDR3 RAM

On-Board Flash Storage

4 GB

Rackmount

Yes

Operating TemperatureDownloads here five nights at freddy's mac freec free download.

-10 to 45° C (14 to 113° F)

Operating Humidity

10 to 90% Noncondensing

Certifications

CE, FCC, IC